共找到 150 條與 端口port 相關的標準，共 10 頁
This document includes standards developed as part of the family of messages targeted for the exchange of information about the conduct of clinical
HL7 Version 3 Standard: Regulated Studies - Periodic Reporting of Clinical Trials Laboratory Results, , Release 1
本文件定義了子系統接口網關的數據模型,規定了子系統接口網關與主站進行信息交互的數據配置要求。 本文件適用于數據采集型子系統接口網關的設計、開發和測試
Customer energy management system—Part 3-2: Data configuration of subsystem gateway
本文件適用于給無法配置距離超過一跳的PCP服務器地址的PCP客戶端建立成功的PCP通信場景
Technical requirements for PCP proxy
本文件規定了 300 mm 晶圓半導體設備裝載端口的尺寸要求，主要包括半導體設備與產線之間的物 理接口。 本文件適用于半導體設備設計與制造領域
300mm Semiconductor Equipment Loadport Requirements
FABRIC, PORT PATTERN, KNIT ***TO BE USED WITH FORD WSS-M99P1111-A***
This SAE Aerospace Standard (AS) establishes the requirements for port preparation@ installation@ and removal procedure for AS5550 fitting assembly
Fitting Assembly – 24Degree Cone Flareless per AS5827@ 5080 psi@ Port Connection Port Preparation@ Installation and Removal of AS5550 and AS5865
Technical requirements and measurement methods for performance of mobile terminals supporting BeiDou Electromagnetic compatibility performance
本文件適用于車聯網路側無線通信設備，包括用于車聯網的車路無線通信終端設備、無線智能交通設備以及無線智能監控設備，如無線智能攝像頭、無線信號控制設備和路側設備等無線通信設備
Electromagnetic compatibility requirements and measurement methods for Internet of Vehicles communication equipment Part 1: Roadside wireless communication terminals
本文件適用于車載無線通信終端設備，包括用于通信的車載無線中短程通信設備和廣域通信設備，如車載藍牙設備、車載無線局域網設備、車載蜂窩無線通信設備以及其它車載無線通信等設備
Electromagnetic compatibility requirements and measurement methods for Internet of Vehicles communication equipment Part 2: Vehicle-mounted wireless communication terminals
Specifications and methods of measurement on two-way subscriber port used in CATV systems
Adapter@ Port Connection to Flareless@ 24 Degree Cone@ Metric
本標準規定了軍用微波接力通信設備（以下簡稱微波接力設備）與檢測設備之間的接口要求。 本標準適用于軍用微波接力通信設備和檢測設備的論證、研制、生產和驗收
Measure and test interface for military microwave relay communication equipment
FABRIC, PORT BASE PATTERN, KNIT ***TO BE USED WITH FORD WSS-M99P1111-A***
GB/T 14598的本部分以IEC 61000-4-18為基礎，參考了該出版物的適用部分，規定了對1MHz和100kHz脈沖群抗擾度試驗的一般要求，這些試驗適用于電力系統繼電保護所用的量度繼電器和保護裝置。包括與這些設備一起使用的控制、監視和過程接口設備。 試驗的目的是驗證被試裝置在受到激勵，并
Electrical relays.Part 22-1:Electrical disturbance tests for measuring relays and protection equipment.1 MHz burst immunity tests
本文件規定了電氣和電子設備對交流電源端口2kHz~150kHz差模傳導騷擾和通信信號的抗擾度要求和試驗方法。 本文件的目的是建立電氣和電子設備交流電源端口經受差模傳導騷擾和通信信號試驗的通用和可重復性準則。 本文件規定了: ———試驗波形; ———試驗等級范圍; ———試驗設備; ———試驗布置
Electromagnetic compatibility—Testing and measurement techniques—Part 19: Test for immunity to conducted, differential mode disturbances and signalling in the frequency range 2 kHz to 150 kHz at a.c.
